<?xml version="1.0" encoding="UTF-8"?><rss xmlns:dc="http://purl.org/dc/elements/1.1/" xmlns:content="http://purl.org/rss/1.0/modules/content/" xmlns:atom="http://www.w3.org/2005/Atom" version="2.0"><channel><title><![CDATA[Reactor 3D Mesh Workshops]]></title><description><![CDATA[Reactor 3D Mesh Workshops]]></description><link>https://reactor3d.hashnode.dev</link><generator>RSS for Node</generator><lastBuildDate>Fri, 20 Nov 2026 18:11:07 GMT</lastBuildDate><atom:link href="https://reactor3d.hashnode.dev/rss.xml" rel="self" type="application/rss+xml"/><language><![CDATA[en]]></language><ttl>60</ttl><item><title><![CDATA[AA Battery Holder for a Shallow Drawer]]></title><description><![CDATA[Model four AA cradles with chosen clearances, closed ends, and a continuous floor. Follow seven CAD steps and download the STL.]]></description><link>https://reactor3d.hashnode.dev/aa-battery-holder-for-a-shallow-drawer</link><guid isPermaLink="true">https://reactor3d.hashnode.dev/aa-battery-holder-for-a-shallow-drawer</guid><category><![CDATA[cad]]></category><category><![CDATA[3D printing]]></category><dc:creator><![CDATA[Shawn lee]]></dc:creator><pubDate>Wed, 18 Nov 2026 03:45:45 GMT</pubDate><content:encoded><![CDATA[<p><em>AI disclosure: This edition was prepared by an AI agent from the published Reactor 3D tutorial and its original interface screenshots. No physical printing, cell-fit, drawer-clearance, or durability testing was performed for this edition.</em></p>
<h2>Four AA cells, lying flat</h2>
<p>Make an 80 × 58 × 10 mm 3D printed battery holder that separates four AA cells in shallow horizontal cradles.</p>
<p>Start with an empty <strong>Solid Model</strong> project in <strong>Modeling</strong>, with English controls and millimeters. This lesson uses a cube, one cylinder, a stepped Array, Cut, and Fillet. The result is one part, with no assembly or electrical contacts.</p>
<p>The cell envelope used here is <strong>14.5 mm diameter × 50.5 mm long</strong>. Measure your own cells before adapting it. A matching cell sits about <strong>16.9 mm above the base bottom</strong> in this geometry; allow at least 20 mm of unobstructed drawer height, then check the first print in the actual drawer. This is a CAD prototype, with physical fit still to be tested.</p>
<table>
<thead>
<tr>
<th>Design target</th>
<th>Value</th>
</tr>
</thead>
<tbody><tr>
<td>Base width, depth, height</td>
<td>80 × 58 × 10 mm</td>
</tr>
<tr>
<td>Four troughs</td>
<td>Ø15.2 × 52.5 mm long</td>
</tr>
<tr>
<td>Center spacing</td>
<td>20 mm along X</td>
</tr>
<tr>
<td>Nominal floor under a trough</td>
<td>2.4 mm</td>
</tr>
<tr>
<td>Closed wall at each end</td>
<td>2.75 mm</td>
</tr>
<tr>
<td>Web between troughs</td>
<td>4.8 mm</td>
</tr>
</tbody></table>
<h2>01. Size the base block</h2>
<p>Choose <strong>Create cube</strong> and place it on the XY grid. Expand its modeling history, select <strong>Cube</strong>, and set <strong>Width 80</strong>, <strong>Depth 58</strong>, and <strong>Height 10 mm</strong>. Choose <strong>Move</strong> and set <strong>Pos X, Y, Z to 0</strong>, all rotations to 0, and <strong>Scale Ratio 1</strong>; name the part <strong>AA Cradle Base</strong>.</p>
<p><img src="https://github.com/IRROBOT/aa-battery-holder/raw/main/step-01.jpg" alt="Cube history and Parameter Palette showing an 80 by 58 by 10 millimeter base" /></p>
<h2>02. Size the first groove tool</h2>
<p>Choose <strong>Create cylinder</strong> and place a separate cylinder on an empty area of the XY grid. Expand its history, select <strong>Cylinder</strong>, and set <strong>Radius 7.6 mm</strong> and <strong>Height 52.5 mm</strong>; name it <strong>AA Groove Tool</strong>. Height becomes the groove’s longitudinal length after the next rotation.</p>
<p><img src="https://github.com/IRROBOT/aa-battery-holder/raw/main/step-02.jpg" alt="Cylinder dimensions set to a 7.6 millimeter radius and 52.5 millimeter height" /></p>
<h2>03. Lay the cylinder across the top</h2>
<p>Select <strong>AA Groove Tool</strong>, choose <strong>Move</strong>, and apply the values below, leaving the scale at 1. The cylinder’s origin is at one end: <strong>Y 26.25</strong> centers its 52.5 mm length between Y −26.25 and +26.25. Its axis lies at the base top, so the lower semicircle removes material while retaining the floor.</p>
<table>
<thead>
<tr>
<th>Transform</th>
<th>X</th>
<th>Y</th>
<th>Z</th>
</tr>
</thead>
<tbody><tr>
<td>Position, mm</td>
<td>−30</td>
<td>26.25</td>
<td>10</td>
</tr>
<tr>
<td>Rotation, degrees</td>
<td>90</td>
<td>0</td>
<td>0</td>
</tr>
</tbody></table>
<p><img src="https://github.com/IRROBOT/aa-battery-holder/raw/main/step-03.jpg" alt="First horizontal groove tool centered within the base with its position and rotation fields visible" /></p>
<h2>04. Array four equally spaced tools</h2>
<p>With the cylinder selected, choose <strong>Array → Stepped</strong>. Pick the positive <strong>X</strong> row axis, set <strong>Rows (including source) 4</strong> and <strong>Step Distance 20 mm</strong>, then pick <strong>Y</strong> as the column axis and set <strong>Columns (including source) 1</strong>. Check the four-cylinder preview and choose <strong>Confirm</strong>; column spacing has no effect for one column.</p>
<p><img src="https://github.com/IRROBOT/aa-battery-holder/raw/main/step-04.jpg" alt="Stepped Array showing X rows of four at 20 millimeter spacing and one Y column" /></p>
<h2>05. Cut the four cradles</h2>
<p>Select <strong>AA Cradle Base</strong> and choose <strong>Cut operation</strong>. Keep it as <strong>Target part</strong>, add <strong>AA Groove Tool</strong> and all three Array copies as tools, and leave <strong>Keep source parts</strong> off. The preview should show four blind half-round troughs with closed ends; choose <strong>Confirm</strong>.</p>
<p><img src="https://github.com/IRROBOT/aa-battery-holder/raw/main/step-05.jpg" alt="Cut preview with the base as target, four cylinder tools selected, and Keep source parts disabled" /></p>
<h2>06. Soften the outside upper rim</h2>
<p>Choose <strong>Fillet</strong> and select the four straight edges around the base’s <strong>outside top perimeter</strong>. Set <strong>Size 0.8 mm</strong>, check that the group contains four edges, and choose <strong>Confirm</strong>. Keep the groove lips and internal floor edges out of this selection.</p>
<p><img src="https://github.com/IRROBOT/aa-battery-holder/raw/main/step-06.jpg" alt="Four outside upper perimeter edges selected for a 0.8 millimeter Fillet" /></p>
<h2>07. Export the single STL</h2>
<p>Choose <strong>File → Export STL</strong>, keep <strong>All visible models</strong> at one model, and choose <strong>Download in browser</strong>. Wait for the export to show <strong>Completed</strong>, then save the single file as <code>aa-battery-holder.stl</code>. Keep the flat bottom on the print bed with the open cradles facing upward.</p>
<p><img src="https://github.com/IRROBOT/aa-battery-holder/raw/main/step-07.jpg" alt="STL export dialog selecting all one visible model and Download in browser" /></p>
<h2>Adjusting the holder for your cells</h2>
<p>The chosen groove diameter adds <strong>0.7 mm total diametral clearance</strong>, or 0.35 mm radially, to the 14.5 mm cell envelope. The 52.5 mm length adds <strong>2 mm total end clearance</strong>. These are starting design choices, not a universal printer allowance or a press fit.</p>
<p>Edit the cylinder radius or length in the project when adapting the fit. Retain material between grooves: the current web is <strong>20 − 15.2 = 4.8 mm</strong>. End-wall thickness is <strong>(base depth − groove length) ÷ 2</strong>; if the length changes, also set the cylinder’s Y position to half that length to keep both end walls equal. Uniform STL scaling changes cell clearance, spacing, and the base together.</p>
<h2>Related modeling lessons</h2>
<ul>
<li><a href="https://reactor3d.xyz/en/tutorials/how-to-use-array-solid-model">Array controls and source-linked copies</a></li>
<li><a href="https://reactor3d.xyz/en/tutorials/boolean-operations-union-subtract-intersect">Boolean Union, Cut, and Intersect</a></li>
<li><a href="https://reactor3d.xyz/en/tutorials/fillet-vs-chamfer-online-cad">Fillet and Chamfer selection</a></li>
</ul>
<h2>Project files</h2>
<p>Download the public <a href="https://api.reactor3d.xyz/tutorials/en/aa-battery-holder/resources/6bb673db-b5f2-4c1b-a945-07d1780e3478/download">aa-battery-holder.stl</a> for the finished four-cell holder. The source text mentions an editable RD, but its attachment section currently exposes only this STL. No editable project file is included in this edition. STL does not retain the editable modeling history; keep your own project when following the steps.</p>
<h2>Practical tips for 3D printing</h2>
<p>Use a calibrated printer profile and inspect the sliced groove floors before printing. The open-up orientation keeps support material out of the cradles. Print one holder first and check that each cell lifts out freely and the drawer closes without contact. This open rack is for stationary storage; it has no lid, retention clip, charging function, or electrical contacts.</p>
<p>Source: <a href="https://reactor3d.xyz/en/tutorials/aa-battery-holder">AA Battery Holder for a Shallow Drawer</a>, by the Reactor 3D Team, published November 18, 2026. Original instructions and interface screenshots are republished with the site owner's authorization.</p>
]]></content:encoded></item><item><title><![CDATA[Design a 3D Printed Coaster]]></title><description><![CDATA[Model a 100 mm coaster with a 94 mm recess and seven blind channels. Follow 13 CAD steps, review the continuous floor, and download the STL.]]></description><link>https://reactor3d.hashnode.dev/design-a-3d-printed-coaster</link><guid isPermaLink="true">https://reactor3d.hashnode.dev/design-a-3d-printed-coaster</guid><category><![CDATA[cad]]></category><category><![CDATA[3D printing]]></category><dc:creator><![CDATA[Shawn lee]]></dc:creator><pubDate>Tue, 17 Nov 2026 03:49:50 GMT</pubDate><content:encoded><![CDATA[<p><em>AI disclosure: This edition was prepared by an AI agent from the published Reactor 3D tutorial and its original interface screenshots. No physical printing, heat-resistance, leakage, or grip testing was performed for this edition.</em></p>
<h2>A coaster with a continuous bottom</h2>
<p>Design a 3D printed coaster with a rounded square outline, a shallow cup recess, and seven blind channels, starting from a blank Solid Model project in Reactor 3D. You will use a concentric sketch copy for the rim and a stepped body array for the repeated grooves, then export one STL for slicing.</p>
<p>These are chosen design dimensions for a prototype. The recess accommodates a measured cup footprint up to 90 mm, leaving at least 2 mm to each straight side of the 94 mm pocket; check your own cup before adapting the dimensions. The channels collect small amounts of condensation inside the coaster rather than passing through its base.</p>
<table>
<thead>
<tr>
<th>Feature</th>
<th>Design dimension</th>
</tr>
</thead>
<tbody><tr>
<td>Overall envelope</td>
<td>100 × 100 × 5 mm</td>
</tr>
<tr>
<td>Outer plan corners</td>
<td>R12 mm</td>
</tr>
<tr>
<td>Cup recess</td>
<td>94 × 94 mm, R9 corners, 2 mm deep</td>
</tr>
<tr>
<td>Perimeter band</td>
<td>3 mm wide</td>
</tr>
<tr>
<td>Cup floor height</td>
<td>Z = 3 mm</td>
</tr>
<tr>
<td>Channels</td>
<td>Seven, 70 × 3 mm, 10 mm center spacing</td>
</tr>
<tr>
<td>Channel depth</td>
<td>0.8 mm below the cup floor</td>
</tr>
<tr>
<td>Channel floor height</td>
<td>Z = 2.2 mm</td>
</tr>
</tbody></table>
<p>Use millimeters throughout, with Z upward from the world XY plane. This intermediate lesson assumes basic sketch and part selection; allow about 40 minutes. Sign in before exporting and check that your account has a remaining trial export or an appropriate plan.</p>
<h2>01. Center a 100 mm square</h2>
<p>Use a blank Solid Model project in the English <a href="https://reactor3d.xyz/editor">Reactor 3D editor</a>. Enter sketch mode, choose the world XY plane, and use Center rectangle to draw around the axes intersection. Switch to Select, select the closed loop, and edit both dimension badges to 100 mm. The illustrated center is X = 0, Y = 0.1 mm; keep this shared datum for the later slot.</p>
<p><img src="https://github.com/IRROBOT/rounded-coaster-cad/raw/main/step-01.jpg" alt="A centered rectangle on the XY plane with both dimensions set to 100 mm" /></p>
<h2>02. Round all four corners</h2>
<p>With the rectangle selected, enable Vertex Shaping. Right-click each original corner and apply a 12 mm Fillet radius. Repeat for all four corners, then Finish Sketch; each straight side between the arcs is now 76 mm.</p>
<p><img src="https://github.com/IRROBOT/rounded-coaster-cad/raw/main/step-02.jpg" alt="Rounded square sketch with four R12 corner arcs and 76 mm straight sections" /></p>
<h2>03. Extrude the coaster blank</h2>
<p>Select the rounded outer loop and choose Extrude. Set Size to 5 mm, keep Blind and New part selected, and Confirm. The blank grows upward from the world XY plane, with its bottom at Z = 0 and top at Z = 5 mm.</p>
<p><img src="https://github.com/IRROBOT/rounded-coaster-cad/raw/main/step-03.jpg" alt="Extrude preview using a 5 mm blind distance and New part for the coaster blank" /></p>
<h2>04. Offset the inner cup boundary</h2>
<p>Enter a new XY sketch session and open Sketch Copy. Choose Center Point, pick the original closed outer profile, then select Gap, Inside, and a Gap Distance of 3 mm. Confirm the concentric copy; its envelope is 94 × 94 mm with R9 corners, leaving an even perimeter band.</p>
<p><img src="https://github.com/IRROBOT/rounded-coaster-cad/raw/main/step-04.jpg" alt="Sketch Copy settings using Center Point and a 3 mm Inside gap" /></p>
<h2>05. Make a separate pocket tool</h2>
<p>Select the new Sketch Copy loop and Finish Sketch. Extrude that loop by 3 mm with Blind and New part selected, then Confirm. Keep this temporary body separate from the coaster so its height can be positioned independently.</p>
<p><img src="https://github.com/IRROBOT/rounded-coaster-cad/raw/main/step-05.jpg" alt="Three millimeter blind extrusion of the inner profile as a separate pocket cutting body" /></p>
<h2>06. Place the pocket tool above the floor</h2>
<p>Select the new pocket body, choose Move, and expand Transform in the Parameter Palette. Set Pos Z to 3 mm, leaving Pos X and Pos Y at 0, rotations at 0°, and Scale Ratio at 1. The tool now spans Z = 3 to 6 mm, overlapping only the upper 2 mm of the 5 mm blank.</p>
<p><img src="https://github.com/IRROBOT/rounded-coaster-cad/raw/main/step-06.jpg" alt="Pocket cutting body positioned at Z 3 mm with unchanged X and Y transforms" /></p>
<h2>07. Cut the recessed cup area</h2>
<p>Select the coaster blank and choose Cut operation. Keep Part 1 as the Target part and add the inner pocket body, Part 2, as the Tool part. Leave Keep source parts off and Confirm; the result has a 3 mm floor and a rim rising 2 mm above it.</p>
<p><img src="https://github.com/IRROBOT/rounded-coaster-cad/raw/main/step-07.jpg" alt="Cut preview with the coaster as target, the inner body as tool, and Keep source parts off" /></p>
<h2>08. Sketch the first rounded channel</h2>
<p>Start another sketch on the world XY plane and open Straight Slot. Click Pick and place the center 30 mm left of the shared center, at X = -30, Y = 0.1 mm in this example. Set Center Distance to 67 mm, Slot Width to 3 mm, and Rotation to 90°; Overall Length should read 70 mm. Confirm and Finish Sketch.</p>
<p><img src="https://github.com/IRROBOT/rounded-coaster-cad/raw/main/step-08.jpg" alt="Straight Slot with 67 mm center distance, 3 mm width, 90 degree rotation, and 70 mm overall length" /></p>
<h2>09. Extrude a channel cutting body</h2>
<p>Select the small closed slot and choose Extrude. Use Size 1.8 mm, Blind, and New part, then Confirm. This temporary cutter extends above the eventual channel floor so it can intersect the recessed cup area cleanly.</p>
<p><img src="https://github.com/IRROBOT/rounded-coaster-cad/raw/main/step-09.jpg" alt="Slot profile extruded 1.8 mm as a separate cutting body" /></p>
<h2>10. Set the channel floor height</h2>
<p>Select the slot cutting body and choose Move. In Transform, set Pos Z to 2.2 mm; leave X, Y, rotation, and scale unchanged. The tool spans Z = 2.2 to 4 mm, so it removes only 0.8 mm from the cup floor at Z = 3 mm.</p>
<p><img src="https://github.com/IRROBOT/rounded-coaster-cad/raw/main/step-10.jpg" alt="Slot cutting body positioned at Z 2.2 mm to create a shallow blind channel" /></p>
<h2>11. Repeat seven channels with Array</h2>
<p>With the slot body selected, open Array and choose Stepped. Pick the red world X direction as the row axis, set Rows (including source) to 7, and Step Distance to 10 mm. Pick the green world Y direction as the column axis and set Columns (including source) to 1; its spacing is unused. Leave Sync source part features enabled and Confirm.</p>
<p><img src="https://github.com/IRROBOT/rounded-coaster-cad/raw/main/step-11.jpg" alt="Stepped Array preview with seven rows along X at 10 mm spacing and one column along Y" /></p>
<h2>12. Cut all seven blind channels</h2>
<p>Select the coaster first and choose Cut operation. Keep it as the Target part, then add the original slot body and all six array copies as Tool parts. Leave Keep source parts off and Confirm; seven round-ended recesses should remain inside the cup area. Hide the three source sketches and name the finished body Rounded Coaster.</p>
<p><img src="https://github.com/IRROBOT/rounded-coaster-cad/raw/main/step-12.jpg" alt="Cut preview using seven selected slot tools while retaining the continuous coaster floor" /></p>
<h2>13. Export the finished coaster as STL</h2>
<p>Choose File → Export STL. Select All visible models and confirm that the scope contains one model, then click Export. Open the downloaded STL in your slicer as millimeters, place the broad underside on the build plate, and review the 100 × 100 × 5 mm envelope before choosing your own material and print profile.</p>
<p><img src="https://github.com/IRROBOT/rounded-coaster-cad/raw/main/step-13.jpg" alt="STL export dialog with All visible models selected and one model included" /></p>
<h2>Finished result</h2>
<p>The result is one rounded square coaster with a continuous underside, a low perimeter rim, and seven shallow channels. The flat bands between the grooves support the cup; the slots remain blind instead of opening onto the table. The supplied STL contains the single completed body, while the editable RD retains the construction history.</p>
<h2>Project resources</h2>
<p>Use the editable <strong>Rounded Coaster RD</strong> to change the dimensions or pattern, and the <strong>Rounded Coaster STL</strong> to start slicing. Both resources contain this same finished coaster; no assembly is needed.</p>
<h2>Related techniques</h2>
<ul>
<li><a href="https://reactor3d.xyz/en/tutorials/how-to-use-center-rectangle-sketch">Center Rectangle in Sketch</a></li>
<li><a href="https://reactor3d.xyz/en/tutorials/how-to-use-corner-fillet-sketch">Corner Fillet in Sketch</a></li>
<li><a href="https://reactor3d.xyz/en/tutorials/how-to-use-straight-slot-sketch">Straight Slot in Sketch</a></li>
<li><a href="https://reactor3d.xyz/en/tutorials/create-stl-file-online-cad">Create an STL File for 3D Printing</a></li>
</ul>
<h2>Practical tips</h2>
<p>Measure the widest part of the cup that will sit inside the rim, including any flared base. If you enlarge the cup pocket, retain room for the perimeter band and keep every channel end inside the recess. Maintain at least the illustrated channel-floor height when increasing groove depth.</p>
<p>Print a sample before relying on the design around condensation or a hot drink: filament choice, layer bonding, surface finish, and cup temperature affect performance. A closed CAD floor does not guarantee a watertight print. Review solid top and bottom layers in the slicer; optional thin adhesive non-slip backing can protect a table and reduce sliding. Physical heat resistance, leakage, and grip have not been tested for this prototype.</p>
<h2>Download the public practice files</h2>
<p>The original lesson provides an editable <a href="https://api.reactor3d.xyz/tutorials/en/design-3d-printed-coaster/resources/b5439aac-5ae9-4a1f-aa12-c278eb12e3c8/download">rounded-coaster.rd</a> and a slicer-ready <a href="https://api.reactor3d.xyz/tutorials/en/design-3d-printed-coaster/resources/0576dbef-44a3-4769-b229-73f450532e1f/download">rounded-coaster.stl</a>. Both contain the same single finished coaster.</p>
<p>Source: <a href="https://reactor3d.xyz/en/tutorials/design-3d-printed-coaster">Design a 3D Printed Coaster</a>, by the Reactor 3D Team, published November 17, 2026. These original instructions and interface screenshots are republished with the site owner's authorization.</p>
]]></content:encoded></item><item><title><![CDATA[Model and Assemble a Scotch Yoke Mechanism]]></title><description><![CDATA[Model eight Scotch yoke parts, create nine assembly relations, preview a 40 mm stroke, and export the separate printable parts in one STL.]]></description><link>https://reactor3d.hashnode.dev/model-and-assemble-a-scotch-yoke-mechanism</link><guid isPermaLink="true">https://reactor3d.hashnode.dev/model-and-assemble-a-scotch-yoke-mechanism</guid><category><![CDATA[cad]]></category><category><![CDATA[3D printing]]></category><dc:creator><![CDATA[Shawn lee]]></dc:creator><pubDate>Mon, 16 Nov 2026 04:42:00 GMT</pubDate><content:encoded><![CDATA[<p><em>AI disclosure: This edition was prepared by an AI agent from the published Reactor 3D tutorial and its original interface screenshots. No physical printing or fit testing was performed for this edition.</em></p>
<p>Practice this browser CAD workflow in <a href="https://reactor3d.xyz/">Reactor 3D</a>. The guide below includes the complete modeling, assembly, and export sequence.</p>
<h2>Build a guided reciprocating mechanism</h2>
<p>Build an eight-part Scotch yoke mechanism from a blank Reactor 3D Solid Model, assemble its moving joints, and export all printable parts in one STL.</p>
<p>Use millimeters, the world XY plane for the base, and +Z upward. Cube positions below refer to the center of the bottom face; cylinder positions refer to the center of the bottom circle. Unless stated otherwise, use zero rotation and scale 1. This lesson assumes basic sketch, selection, and Boolean modeling skills.</p>
<p>This is a hand-operated CAD demonstrator of rotary-to-linear motion. Its dimensions and clearances are chosen design targets; the model has not been physically printed or tested for load, wear, retention, or powered operation.</p>
<p>Component or target | Dimensions (mm)</p>
<ul>
<li>Ground: 220 x 120 x 8 plate, R6 corners, four 5 mm feet</li>
<li>Crank: R28 disk, 5 thick, 20 eccentric radius</li>
<li>Yoke: 200 x 88 x 6; guide arms 12 wide</li>
<li>Slot: 10.4 wide x 64.4 overall, R5.2 ends</li>
<li>Sliding Block: 10 x 12 x 6, bore 6.4</li>
<li>Each guide: 16 x 32 x 18; window 12.4 x 6.4</li>
<li>Pivot Retainer: Head diameter 16 x 1.2; peg diameter 4.8 x 4</li>
<li>Pin Retainer: Head diameter 11 x 2; peg diameter 3.8 x 4</li>
<li>Output travel: 40 nominal, from a 20 mm crank radius</li>
</ul>
<p>For physical assembly, supply <strong>four full-thread M3 x 30 socket-head screws and four M3 nuts</strong>, plus adhesive appropriate to the printed material for the two retainer pegs. The purchased hardware is excluded from the STL. Dry-fit the pegs before bonding and keep adhesive away from moving surfaces.</p>
<h2>01. Sketch the ground plate</h2>
<p>Start a blank <strong>Solid Model</strong> project in millimeters. Enter sketch mode on <strong>XY</strong> and draw a centered rectangle, 220 mm along X and 120 mm along Y. Use the vertex coordinates (-110, -60), (110, -60), (110, 60), and (-110, 60).</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-5fc92fd7-5be2-4ec6-8414-547b3b7290fd-1600x900-a461e18cec89.webp" alt="Centered 220 by 120 mm ground outline on the XY sketch plane" /></p>
<h2>02. Round the plate corners</h2>
<p>Enable vertex shaping and set all four corner radii to <strong>6 mm</strong> from their vertex menus. Keep the 220 x 120 mm outside envelope, then choose <strong>Finish Sketch</strong>.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-9000e35d-e594-4ad6-aa66-4ae88eb8e57d-1600x900-14a6c70a16b1.webp" alt="Four R6 corners on the ground plate sketch" /></p>
<h2>03. Extrude the ground plate</h2>
<p>Select the closed loop and choose <strong>Extrude</strong>. Use <strong>Blind</strong>, 8 mm, <strong>New part</strong>, and confirm. Name the part <strong>Ground</strong>, keep its position at (0, 0, 0), and hide the source sketch.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-0d2b2184-8341-4bbc-b074-c8a56c6096da-1600x900-5cd0c394f37c.webp" alt="Blind 8 mm extrusion of the rounded ground profile" /></p>
<h2>04. Create one support foot</h2>
<p>Create a cylinder with <strong>Radius 8 mm</strong> and <strong>Height 5 mm</strong>. In <strong>Move</strong>, set its world position to <strong>(-90, -45, -5)</strong> with zero rotation. This puts its top against the underside of Ground.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-b1d65bff-8807-40a3-8f2a-a96c19333d70-1600x900-681dbcd0347a.webp" alt="Support foot seed dimensions and position beneath the ground plate" /></p>
<h2>05. Pattern and join the feet</h2>
<p>Select the foot and open <strong>Array &gt; Stepped</strong>. Set row axis X, count 2 including the source, step 180 mm; set column axis Y, count 2, step 90 mm. Confirm, select Ground first and all four feet next, then <strong>Combine</strong> with <strong>Keep source parts</strong> off.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-f423c4e4-6919-4ad5-81b0-c297cf0d0594-1600x900-4dc3334d62d8.webp" alt="Stepped array settings for four support feet" /></p>
<h2>06. Add the central pivot</h2>
<p>Create a cylinder with <strong>Radius 5 mm</strong>, <strong>Height 6.4 mm</strong>, at world <strong>(0, 0, 8)</strong>. Select Ground first and the cylinder second, then <strong>Combine</strong>, keeping source parts off. The pivot top is Z = 14.4 mm.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-44b5114c-b7e2-400f-81df-0c3d44d2a112-1600x900-5d00f64efa3a.webp" alt="Central pivot boss radius height and world position" /></p>
<h2>07. Cut the pivot retainer seat</h2>
<p>Choose <strong>Hole</strong> on the pivot’s top face. Use <strong>Simple hole</strong>, <strong>Straight</strong>, <strong>Single hole</strong>, diameter <strong>5 mm</strong>, and depth <strong>5 mm</strong>. In <strong>Position in part coordinates</strong>, use X = 0 and Y = 0; the selected top is local Z = 14.4 mm.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-d107b70a-8a2c-43af-a5bb-a6b680771a4d-1600x900-eca9ccbb61f6.webp" alt="Five millimeter diameter blind retainer seat in the ground pivot" /></p>
<h2>08. Pattern the guide mounting cutters</h2>
<p>Create a cylinder cutter with radius <strong>1.7 mm</strong>, height <strong>8 mm</strong>, at <strong>(-70, -12, 0)</strong>. Use <strong>Array &gt; Stepped</strong>: X count 2, step 140 mm; Y count 2, step 24 mm, both including the source. These four cutters produce 3.4 mm clearance holes for M3 screws.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-7389e751-d9ab-4c40-a1d5-ccb0e2e69352-1600x900-993d1cd6f11c.webp" alt="Two by two mounting-hole cutter array with 140 and 24 mm steps" /></p>
<h2>09. Cut the four mounting holes</h2>
<p>Select Ground as the target and the four mounting cylinders as tools. Choose <strong>Cut</strong>, switch <strong>Keep source parts</strong> off, and confirm. The holes pass through the full 8 mm plate at X = +/-70 mm and Y = +/-12 mm.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-1330c707-e36f-401d-a0c7-76a61046670a-1600x900-9fe17a1d48f2.webp" alt="Ground selected as the cut target with four mounting cutters" /></p>
<h2>10. Size and position the crank disk</h2>
<p>Create a cylinder with <strong>Radius 28 mm</strong> and <strong>Height 5 mm</strong>, at world <strong>(0, 0, 9)</strong> with zero rotation. The disk has a 1 mm gap above the plate. Name this blank <strong>Crank Blank</strong>; the finished part will be <strong>Crank</strong>.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-77fb7d58-4fa9-4162-bac2-ea18db805774-1600x900-9a2a2aafd9d1.webp" alt="Crank blank with radius 28 height 5 and position zero zero nine" /></p>
<h2>11. Bore the crank center</h2>
<p>Choose <strong>Hole</strong> on the disk’s top face: diameter <strong>10.4 mm</strong>, depth <strong>5 mm</strong>, straight single hole. Set local X = 0 and Y = 0 at top Z = 5 mm. Rename the finished part <strong>Crank</strong>; the 10 mm pivot has 0.2 mm radial clearance in this bore.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-389f65c1-936e-4783-9a7f-afdece889de8-1600x900-c60642499183.webp" alt="Crank central bore with diameter 10.4 mm and depth 5 mm" /></p>
<h2>12. Add the eccentric pin</h2>
<p>Create a cylinder with <strong>Radius 3 mm</strong>, <strong>Height 9 mm</strong>, at world <strong>(20, 0, 14)</strong>. Combine it into Crank, keeping source parts off. Its 20 mm offset from the disk axis sets a nominal 40 mm yoke stroke.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-27c317ce-7182-4596-b395-99ad9d2d473a-1600x900-a2ea14837031.webp" alt="Eccentric crank pin centered 20 mm from the pivot" /></p>
<h2>13. Cut the pin retainer seat</h2>
<p>On the pin’s top face, make a straight single <strong>Hole</strong>, diameter <strong>4 mm</strong>, depth <strong>5 mm</strong>. Use Crank-local X = 20 and Y = 0, at local top Z = 14 mm. The hole stops at world Z = 18 mm.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-a2118111-81b3-4e8a-9f6d-9ce406d672fd-1600x900-1c6976b804e4.webp" alt="Four millimeter blind seat at the eccentric pin top" /></p>
<h2>14. Sketch the yoke and its guide arms</h2>
<p>Hide Ground and Crank. On XY, use <strong>Line</strong> to draw and close the outline below; use each vertex menu’s <strong>Set Coordinates</strong> to enter the exact positions. The overall outline is 200 x 88 mm, with 12 mm wide guide arms and a 22 mm wide central frame.</p>
<p>Vertex order | X, Y (mm)</p>
<ul>
<li>1-4: (-11, -44), (11, -44), (11, -6), (100, -6)</li>
<li>5-8: (100, 6), (11, 6), (11, 44), (-11, 44)</li>
<li>9-12: (-11, 6), (-100, 6), (-100, -6), (-11, -6)</li>
</ul>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-09a4f6f8-1540-42a4-ab9a-e4b114679f53-1600x900-e670af1c94a0.webp" alt="Closed yoke outline with two 200 mm spanning guide arms" /></p>
<h2>15. Shape the yoke junctions</h2>
<p>Set <strong>Radius 3 mm</strong> at all twelve vertices, including the four inside shoulders where the arms join the frame. The rounded shoulders remove the sharp notches without changing the outside 200 x 88 mm envelope. Finish the sketch.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-08e53ee4-ccb1-4b9a-b167-e92f6c48e44e-1600x900-6d3c691b1933.webp" alt="R3 shaping at the yoke outer corners and inside shoulders" /></p>
<h2>16. Give the yoke its thickness</h2>
<p>Extrude the loop <strong>Blind 6 mm</strong> as a <strong>New part</strong>, then name it <strong>Yoke</strong>. Use <strong>Move</strong> to set world position <strong>(20, 0, 16)</strong>, zero rotation. Hide the source sketch; the yoke bottom now clears the crank disk by 2 mm.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-51585539-5df0-469a-b24b-33f138237296-1600x900-01985119421f.webp" alt="Six millimeter extrusion of the rounded yoke profile" /></p>
<h2>17. Create the straight slot cutter</h2>
<p>Create a cube, <strong>Width 10.4 mm</strong>, <strong>Depth 54 mm</strong>, <strong>Height 6 mm</strong>. Place its bottom-center at world <strong>(20, 0, 16)</strong> with zero rotation. This cutter makes the straight portion of the through-slot.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-c4ed0a01-35f9-49ed-a512-3321a323d790-1600x900-17b5ffc5d640.webp" alt="Yoke straight slot cutter sized 10.4 by 54 by 6 mm" /></p>
<h2>18. Mirror the rounded slot end</h2>
<p>Create a cylinder with <strong>Radius 5.2 mm</strong>, <strong>Height 6 mm</strong>, at <strong>(20, -27, 16)</strong>. Use <strong>Mirror Duplicate</strong>, choose the <strong>World XZ plane</strong>, and confirm. The two cylinders form semicircular ends centered at Y = -27 and +27 mm.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-4b79ebc9-95bf-45fa-87fc-401b5bac9df3-1600x900-3424f663be00.webp" alt="Slot-end cylinder mirrored across the World XZ plane" /></p>
<h2>19. Cut the complete yoke slot</h2>
<p>Select Yoke first, then the straight cutter and both end cylinders. Choose <strong>Cut</strong>, keeping source parts off, and confirm. The through-slot is <strong>10.4 mm wide</strong>, <strong>64.4 mm long overall</strong>, with R5.2 ends.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-a1d5ce37-c151-4db7-a364-da391fce8708-1600x900-25a1223ce9fc.webp" alt="Three cutters forming the complete rounded yoke through-slot" /></p>
<h2>20. Create the sliding pin block</h2>
<p>Create a cube, <strong>Width 10 mm</strong>, <strong>Depth 12 mm</strong>, <strong>Height 6 mm</strong>, at world <strong>(20, 0, 16)</strong>. Name it <strong>Sliding Block</strong>. Its two X-facing sides have 0.2 mm clearance per side inside the 10.4 mm slot.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-b1873c08-1ed7-408c-b691-0d53be19f27f-1600x900-5fa925958413.webp" alt="Sliding Block dimensions and assembled starting position" /></p>
<h2>21. Bore the sliding block</h2>
<p>On the block’s top face, make a straight single <strong>Hole</strong>, diameter <strong>6.4 mm</strong>, depth <strong>6 mm</strong>. Set local X = 0 and Y = 0 at local top Z = 6 mm. This gives the 6 mm crank pin 0.2 mm radial clearance.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-8ecfcbd0-0fa0-4c6f-870e-6fa99b5e7ebb-1600x900-f6ba52dacc7d.webp" alt="Through-bore in Sliding Block with 6.4 mm diameter" /></p>
<h2>22. Create the left guide body</h2>
<p>Create a cube, <strong>Width 16 mm</strong>, <strong>Depth 32 mm</strong>, <strong>Height 18 mm</strong>, at world <strong>(-70, 0, 8)</strong>. Name it <strong>Left Guide</strong>. Its bottom sits on Ground and its two mounting holes will line up with the left pair in the plate.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-7ac9f39a-cbf3-48f6-bf16-22d0117984e6-1600x900-38a9798f0afa.webp" alt="Left Guide blank sized 16 by 32 by 18 mm" /></p>
<h2>23. Size the rectangular guide window</h2>
<p>Create a cube cutter, <strong>Width 16 mm</strong>, <strong>Depth 12.4 mm</strong>, <strong>Height 6.4 mm</strong>, at <strong>(-70, 0, 15.8)</strong>. It crosses the full X thickness of the guide. The window leaves 0.2 mm clearance on each Y and Z face of the 12 x 6 mm yoke arm.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-bf63533a-b295-4f0a-898b-2b3652b37dfe-1600x900-a19fbb170186.webp" alt="Rectangular guide-window cutter and its 15.8 mm bottom elevation" /></p>
<h2>24. Mirror the guide mounting cutter</h2>
<p>Create a cylinder cutter with <strong>Radius 1.7 mm</strong>, <strong>Height 18 mm</strong>, at <strong>(-70, -12, 8)</strong>. Use <strong>Mirror Duplicate &gt; World XZ plane</strong> to create the cutter at Y = +12 mm. Both cutters align with the 3.4 mm holes already in Ground.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-a8af0778-8d09-46e7-aa3a-205a903a222d-1600x900-4a09e8568cf0.webp" alt="Guide mounting cylinder mirrored to the opposite Y position" /></p>
<h2>25. Open the guide window and bolt holes</h2>
<p>Select Left Guide first, then the window cutter and both mounting cylinders. Choose <strong>Cut</strong>, turn <strong>Keep source parts</strong> off, and confirm. The result has one horizontal rectangular window and two vertical through-holes.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-ccd5e51d-b510-4294-98db-5a8860a6b6a1-1600x900-bb460549b8d1.webp" alt="Left Guide cut with one window and two mounting bores" /></p>
<h2>26. Create the opposite guide</h2>
<p>Select Left Guide and use <strong>Mirror Duplicate &gt; World YZ plane</strong>. Name the reflected part <strong>Right Guide</strong>. Its geometry is centered at world X = +70 mm; the mirrored part’s transform origin may retain the source origin, so use the visible geometry when checking its placement.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-1811aa01-f6bc-401a-94c2-0c97d3aa9e78-1600x900-e4b8f3166121.webp" alt="Right Guide mirrored across the World YZ plane" /></p>
<h2>27. Create the pivot retainer head</h2>
<p>Create a cylinder, <strong>Radius 8 mm</strong>, <strong>Height 1.2 mm</strong>, at world <strong>(0, 0, 14.4)</strong>. This head sits 0.4 mm above the crank and leaves another 0.4 mm below the yoke.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-3a00f2c3-ac2e-4d55-a893-4e7fb85ab689-1600x900-a233d1075b55.webp" alt="Pivot retainer head diameter height and assembled elevation" /></p>
<h2>28. Join the pivot retainer peg</h2>
<p>Create a cylinder, <strong>Radius 2.4 mm</strong>, <strong>Height 4 mm</strong>, at <strong>(0, 0, 10.4)</strong>. Combine it with the head and name the result <strong>Pivot Retainer</strong>. The peg has 0.1 mm radial clearance and 1 mm bottom clearance in the 5 mm seat.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-4ce70ee8-685e-4d4d-8300-6797f3ada582-1600x900-736359a8f9bd.webp" alt="Pivot retainer peg dimensions before combining it with the head" /></p>
<h2>29. Create the pin retainer head</h2>
<p>Create a cylinder, <strong>Radius 5.5 mm</strong>, <strong>Height 2 mm</strong>, at <strong>(20, 0, 23)</strong>. Its underside is 1 mm above the block and yoke tops, allowing them to move beneath it.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-d3562c55-37e9-4769-83c2-1143bca6f482-1600x900-62efad6fd359.webp" alt="Pin retainer head with 5.5 mm radius and 2 mm height" /></p>
<h2>30. Join the pin retainer peg</h2>
<p>Create a cylinder, <strong>Radius 1.9 mm</strong>, <strong>Height 4 mm</strong>, at <strong>(20, 0, 19)</strong>. Combine it with the head and name the result <strong>Pin Retainer</strong>. Its peg has 0.1 mm radial clearance and 1 mm bottom clearance in the crank pin’s 4 mm seat.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-2533c66e-3d4f-4bce-9400-ca52e45955a6-1600x900-5c44728cb984.webp" alt="Pin retainer peg at world Z19 before the head and peg are combined" /></p>
<h2>31. Create the crank revolute joint</h2>
<p>Show all eight parts and enter <strong>Assemble</strong>. Create an assembly named <strong>Scotch Yoke Drive</strong>, set Ground as the position reference, and capture axis anchors from the Ground pivot’s outside cylinder and Crank’s central bore. In <strong>Relations</strong>, connect them with <strong>Revolute</strong>, aligned to Z; its RZ angle drives the crank.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-cb44f45d-aced-44b0-8930-6a13ddd9b94c-1600x900-287800404e49.webp" alt="Ground to Crank revolute joint in the Relations panel" /></p>
<h2>32. Keep the yoke at its working height</h2>
<p>Capture a plane from Ground’s broad top face at Z = 8 mm and a plane from Yoke’s top face at Z = 22 mm, both facing +Z. Add a <strong>Planar</strong> relation, Ground reference to Yoke target, with <strong>Distance 14 mm</strong>. This keeps the yoke horizontal while allowing in-plane travel.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-0ce62e0b-e291-4cc8-acd3-bdee0acf29a6-1600x900-fe5843d334cc.webp" alt="Ground top and Yoke top planar relation with 14 mm offset" /></p>
<h2>33. Constrain the yoke to X travel</h2>
<p>Capture planes from Ground’s +Y outside face at Y = 60 mm and Yoke’s +Y end face at Y = 44 mm. Add a <strong>Planar</strong> relation with Ground as reference, Yoke as target, and <strong>Distance -16 mm</strong>. Together, the two plane relations guide the yoke along X.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-2dcd8b96-e0d5-4fd5-95f0-32c974410dd4-1600x900-f91c047ffac4.webp" alt="Yoke side-plane relation with negative 16 mm offset" /></p>
<h2>34. Connect the block to the crank pin</h2>
<p>Capture an axis from Crank’s eccentric pin and an axis from Sliding Block’s bore. Add a <strong>Revolute</strong> relation between these Z axes. The block follows the eccentric pin while remaining free to turn relative to Crank.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-759c8cbf-4b9c-4d47-816d-ded65e5f4262-1600x900-d077844a6606.webp" alt="Crank pin to Sliding Block revolute relation" /></p>
<h2>35. Guide the block across the yoke</h2>
<p>Capture a plane from Yoke’s +X arm end, world X = 120 mm at the starting pose, and one from Sliding Block’s +X face, world X = 25 mm. Add <strong>Planar</strong>, Yoke reference to block target, <strong>Distance -95 mm</strong>. This keeps the block centered across the slot while allowing it to slide along Y.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-11e0cbc1-725f-44da-9d82-603c46511d35-1600x900-917e8c379adf.webp" alt="Yoke to Sliding Block planar relation with negative 95 mm offset" /></p>
<h2>36. Fix the left guide to Ground</h2>
<p>Capture a plane on Left Guide. Add a <strong>Fixed</strong> relation from Ground’s pivot axis anchor to that plane, preserving the current placement at <strong>(-70, 0, 8)</strong>. The relation locks the guide to Ground rather than to the moving yoke.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-954907b1-5626-4945-8898-370106d270ed-1600x900-16b22193ea93.webp" alt="Fixed relation attaching Left Guide to Ground" /></p>
<h2>37. Fix the right guide to Ground</h2>
<p>Capture a plane on Right Guide and add a <strong>Fixed</strong> relation from Ground’s pivot axis anchor. Preserve the reflected guide’s current placement at geometric center X = +70 mm. Both guide windows should surround the yoke arms.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-59adb3cf-03a8-4459-af6e-8ed02ef5a7c8-1600x900-2c4c11980d2e.webp" alt="Fixed relation attaching the mirrored Right Guide to Ground" /></p>
<h2>38. Fix the pivot retainer</h2>
<p>Capture a plane on Pivot Retainer and add <strong>Fixed</strong> from Ground’s pivot axis anchor, preserving its current placement. The cap belongs to Ground, so the crank can rotate beneath its head.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-d32bb258-7c4b-4615-bb22-5637d62ef6f7-1600x900-41896350fec8.webp" alt="Pivot Retainer fixed to the Ground pivot anchor" /></p>
<h2>39. Fix the pin retainer to Crank</h2>
<p>Capture a plane on Pin Retainer. Add <strong>Fixed</strong> from Crank’s eccentric pin axis anchor to this plane, preserving its current placement. The assembly now uses <strong>two Revolute, three Planar, and four Fixed relations</strong>.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-8717821f-cce3-49c0-a478-43b8adc72e10-1600x900-bf7cc03b9497.webp" alt="Pin Retainer fixed to the moving Crank pin anchor" /></p>
<h2>40. Preview the reciprocating movement</h2>
<p>Change the Ground-Crank revolute joint’s <strong>Angle RZ</strong> to 90 degrees, then try 180 and -90 degrees. The yoke passes through center at quarter turns and reaches X = +20 and -20 mm at opposite dead centers. Keep both arms inside the guide windows throughout this 40 mm stroke.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-5224619e-99ee-45ca-b87e-2d22cc075118-1600x900-cffc87ab7487.webp" alt="Revolute angle controls previewing the yoke near its centered position" /></p>
<h2>41. Create a looping revolution</h2>
<p>In <strong>Workspace</strong>, create the motion asset <strong>One Revolution</strong> with <strong>Duration 4000 ms</strong>. Choose the crank’s RZ driven joint, add a 0 degree keyframe at 0 ms and a 360 degree keyframe at 4000 ms, then enable <strong>Loop</strong> and press <strong>Play</strong>. Pause and clear the preview before returning to modeling.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-905c5774-b96d-4c6b-8aaa-17cdd8e2be97-1600x900-4c08781a86c6.webp" alt="One Revolution motion asset with 4000 ms duration and Loop enabled" /></p>
<h2>42. Arrange the eight parts for printing</h2>
<p>Keep an assembled RD before changing the layout. In Modeling, use <strong>Move</strong> and <strong>Rotate Part</strong> with the values below; leave Rot Y and Rot Z at zero. Move Left Guide before Right Guide, because the mirrored geometry also follows its source.</p>
<p>Part | Move Pos X, Y, Z (mm) | Rot X (degrees)</p>
<ul>
<li>Ground: 0, 0, 5; 0</li>
<li>Crank: -90, 100, 0; 0</li>
<li>Sliding Block: -38, 155, 0; 0</li>
<li>Left Guide: -90, 155, 0; 0</li>
<li>Right Guide: -225, 0, 8; 0</li>
<li>Pivot Retainer: -10, 175, 1.2; 180</li>
<li>Pin Retainer: 15, 175, 2; 180</li>
<li>Yoke: 45, 110, 0; 0</li>
</ul>
<p>Right Guide’s numbers describe its retained transform origin; after moving the source, these values put its actual bottom-center at (-65, 155, 0). Ground rests on its feet, both retainers rest on their broad heads with pegs up, and every independent part has a gap around it.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-90e7b22c-0324-4082-bd37-02b671be5b17-1600x900-e5fe86f644cf.webp" alt="Eight separated printable parts with both retainer heads facing the bed" /></p>
<h2>43. Export one STL containing every part</h2>
<p>Choose <strong>File &gt; Export STL</strong>. In <strong>Choose export scope</strong>, select <strong>All visible models</strong>, confirm that it includes eight models, then choose <strong>Download in browser</strong>. Export one file, <strong>scotch-yoke-mechanism.stl</strong>; keep the parts independent rather than combining the mechanism into one solid.</p>
<p><img src="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/image-e0914c16-61cb-48ca-9a81-9b33b0101735-1600x900-80bb0d79a859.webp" alt="STL export scope selecting all eight visible models in one file" /></p>
<h2>Finished mechanism and physical assembly</h2>
<p>The crank pin carries a separate sliding block inside the yoke slot. The block travels across the slot as the yoke moves through the two guides, producing a nominal 40 mm stroke without a connecting rod. At either stroke end, the 200 mm bar extends 2 mm beyond the far outside face of the engaged guide.</p>
<p>For a printed demonstrator, place Crank over Ground’s pivot and fit Pivot Retainer into its seat. Slide the yoke arms through both guides, place the guides over the plate holes, and fit Sliding Block over the eccentric pin inside the slot. Fit Pin Retainer last. Install the four M3 x 30 screws from the guide tops and secure the nuts below Ground; the 5 mm feet leave room beneath the plate. Bond only the two retainer pegs after confirming free movement.</p>
<h2>Project file</h2>
<p><a href="https://assets.reactor3d.xyz/tutorials-page/articles/scotch-yoke-mechanism/resources/144489f7ae679a5201af2becfb192c1e8092d2df30105ada1771adf295b7d7d8.stl">scotch-yoke-mechanism.stl</a> contains the eight separated printable parts. Split the imported file into independent objects in your slicer to arrange them across suitable build plates. STL does not retain the editable feature history, part names, joints, or motion asset; keep the assembled RD for editing.</p>
<h2>Practical tips</h2>
<ul>
<li>The supplied separated layout occupies approximately <strong>263 x 243 x 19.4 mm</strong>. It needs rearrangement or multiple plates on a 220 mm bed; a single STL does not mean a single print plate.</li>
<li>Review supports beneath Ground’s broad elevated plate and bridging or supports across the guide window roofs. Print the two retainers on their broad heads.</li>
<li>The 0.2 mm sliding gaps are per side or radial as specified in the relevant steps. They are CAD allowances, not a guarantee for every printer; start with a small fit trial and remove burrs before assembly.</li>
<li>Turn the disk gently by hand and watch the block at the slot ends. This demonstrator has no established powered speed, load capacity, or retainer pull-out rating.</li>
</ul>
<p>Source: <a href="https://reactor3d.xyz/en/tutorials/scotch-yoke-mechanism">Model and Assemble a Scotch Yoke Mechanism</a>, by the Reactor 3D Team. Interface screenshots and design instructions are from that original tutorial.</p>
]]></content:encoded></item><item><title><![CDATA[How to Edit an STL: Move and Resize a Hole Without Resizing the Plate]]></title><description><![CDATA[Move and resize a hole in an STL without changing the plate dimensions. Follow nine illustrated steps with starting and finished practice models.]]></description><link>https://reactor3d.hashnode.dev/how-to-edit-an-stl-move-and-resize-a-hole-without-resizing-the-plate</link><guid isPermaLink="true">https://reactor3d.hashnode.dev/how-to-edit-an-stl-move-and-resize-a-hole-without-resizing-the-plate</guid><category><![CDATA[3D printing]]></category><category><![CDATA[cad]]></category><dc:creator><![CDATA[Shawn lee]]></dc:creator><pubDate>Sun, 15 Nov 2026 03:43:06 GMT</pubDate><content:encoded><![CDATA[<p>Edit an imported STL in Reactor 3D by filling its existing hole, cutting a smaller hole in a new position, and downloading the edited mesh without changing the plate's outside size.</p>
<p>This article was written with AI assistance using a recorded online modeling walkthrough. All instructional screenshots show the actual editor.</p>
<p>Start with an empty <strong>Mesh Model</strong> project and a closed plate STL matching the starting dimensions below. For the exact practice geometry, download <a href="https://assets.reactor3d.xyz/tutorials-page/articles/how-to-edit-stl-files/resources/e86d5c4538a7b7bfdf19911cfa5d924348b7616fa7b67dbdd3e97e0fb19fff19.rd">stl-editing-start.rd</a>, open it with <strong>Project → Open Local Project</strong>, and begin at Step 02; the STL has already been imported in that project. <a href="https://assets.reactor3d.xyz/tutorials-page/articles/how-to-edit-stl-files/resources/fb442e4b440bb534915f4c641c5579f5320c59aaaa28b05a7f7faa941c78d839.rd">stl-editing-finished.rd</a> provides the completed example.</p>
<ul>
<li><strong>Plate width × depth × thickness:</strong> 70 × 40 × 6 mm</li>
<li><strong>World X bounds:</strong> -35 to 35 mm</li>
<li><strong>World Y bounds:</strong> -20 to 20 mm</li>
<li><strong>Bottom / top Z:</strong> 0 / 6 mm</li>
<li><strong>Existing through-hole:</strong> Diameter 10 mm, center X = -18 / Y = 0</li>
<li><strong>New through-hole target:</strong> Diameter 6 mm, center X = 18 / Y = 0</li>
</ul>
<p>STL stores a triangle mesh rather than the original sketches and dimensions. This lesson adds and removes material with separate tool bodies; it does not recover the source feature history. The simple plate is a practice model for this editing technique.</p>
<h2>01. Import an editable STL</h2>
<p>In a new <strong>Mesh Model</strong> project, choose <strong>File → Import model</strong> and select your STL. Keep <strong>Model editable</strong> enabled and click <strong>Import</strong>. Select the imported entry in the Browser and set its <strong>Name</strong> to <strong>Imported Plate</strong>, pressing Enter to commit the name.</p>
<p>If you opened the starting RD practice project, its imported plate is already ready; continue with the next step.</p>
<img src="https://assets.reactor3d.xyz/tutorials-page/articles/how-to-edit-stl-files/image-42961b65-0d97-4206-9227-19f9c949dfae-1600x900-56e69f74c797.webp" alt="Import model dialog with Model editable enabled for the practice plate" style="display:block;margin:0 auto" />

<h2>02. Check the starting size</h2>
<p>Click the navigation cube's <strong>Top</strong> face, then use <strong>Measure</strong> to select the two outer vertices along the plate's long top edge. The practice plate reads <strong>70.00 mm</strong>; remove the measurement with <strong>Delete</strong> and return to <strong>Select</strong>.</p>
<p>The coordinates below assume the bounds in the starting specifications. For a different STL, establish its actual size, hole center and top/bottom positions before placing either cylinder; camera zoom does not change those dimensions.</p>
<img src="https://assets.reactor3d.xyz/tutorials-page/articles/how-to-edit-stl-files/image-b02d5acf-e07b-472b-bfc7-639ee3d9690e-1600x900-3ff4a6a13cfb.webp" alt="Measure shows the imported plate is 70.00 mm wide between its outer top vertices" style="display:block;margin:0 auto" />

<h2>03. Create a plug for the old hole</h2>
<p>Click <strong>Create cylinder</strong> and place it on empty grid beside the plate. Set <strong>Name</strong> to <strong>Hole Plug</strong> and press Enter, then enter these values in <strong>Dimensions</strong>.</p>
<ul>
<li><strong>Radius:</strong> 5.2 mm</li>
<li><strong>Height:</strong> 6 mm</li>
</ul>
<p>The old hole has a 5 mm radius; the extra 0.2 mm creates radial overlap with the surrounding material.</p>
<img src="https://assets.reactor3d.xyz/tutorials-page/articles/how-to-edit-stl-files/image-f08b3da5-d6e3-4222-9c01-81a4e62b6b45-1600x900-597c0198d396.webp" alt="Hole Plug cylinder with Radius 5.2 mm and Height 6 mm in the Parameter Palette" style="display:block;margin:0 auto" />

<h2>04. Place the plug inside the old hole</h2>
<p>With <strong>Hole Plug</strong> selected, expand <strong>Transform</strong> and enter the world coordinates below. Keep all rotations at zero and <strong>Scale Ratio</strong> at 1.</p>
<ul>
<li><strong>Pos X / Pos Y / Pos Z:</strong> -18 / 0 / 0 mm</li>
<li><strong>Rot X / Rot Y / Rot Z:</strong> 0° / 0° / 0°</li>
</ul>
<p>The plug spans Z = 0–6, matching the plate's bottom and top, so it fills the bore without adding material above or below the plate.</p>
<img src="https://assets.reactor3d.xyz/tutorials-page/articles/how-to-edit-stl-files/image-6f6ace85-b7dc-4a46-aa47-28f3f2f3a066-1600x900-380f9dba1fa7.webp" alt="Hole Plug at world position X minus 18, Y zero, Z zero with zero rotations and scale one" style="display:block;margin:0 auto" />

<h2>05. Combine the plug with the plate</h2>
<p>Select <strong>Imported Plate</strong> first, then hold <strong>Ctrl</strong> and select <strong>Hole Plug</strong> in the Browser. Click <strong>Combine operation</strong>, check <strong>Imported Plate</strong> as <strong>Combine target 1</strong> and <strong>Hole Plug</strong> as <strong>Combine target 2</strong>, and leave <strong>Keep source parts</strong> off.</p>
<p>Click <strong>Confirm</strong> and name the result <strong>Filled Plate</strong>. The old opening should disappear into one continuous top face.</p>
<img src="https://assets.reactor3d.xyz/tutorials-page/articles/how-to-edit-stl-files/image-d0afbd05-1d95-4fe7-a675-4b6b0a4203ac-1600x900-4359d256b83a.webp" alt="Combine panel with Imported Plate as target one, Hole Plug as target two, and Keep source parts off" style="display:block;margin:0 auto" />

<h2>06. Create the new hole cutter</h2>
<p>Click <strong>Create cylinder</strong> and place another cylinder on empty grid. Name it <strong>New Hole Cutter</strong>, press Enter, and set these <strong>Dimensions</strong>.</p>
<ul>
<li><strong>Radius:</strong> 3 mm</li>
<li><strong>Height:</strong> 8 mm</li>
</ul>
<p>This makes a 6 mm diameter opening; the extra cutter height lets it cross both faces of the 6 mm plate.</p>
<img src="https://assets.reactor3d.xyz/tutorials-page/articles/how-to-edit-stl-files/image-4b0e8f75-4bfa-4df7-8d6a-818c17b3a330-1600x900-1f10219012d4.webp" alt="New Hole Cutter cylinder with Radius 3 mm and Height 8 mm" style="display:block;margin:0 auto" />

<h2>07. Position the new opening</h2>
<p>Expand the cutter's <strong>Transform</strong> section and enter the world position below. Keep all rotations at zero and <strong>Scale Ratio</strong> at 1.</p>
<ul>
<li><strong>Pos X / Pos Y / Pos Z:</strong> 18 / 0 / -1 mm</li>
<li><strong>Rot X / Rot Y / Rot Z:</strong> 0° / 0° / 0°</li>
</ul>
<p>The cylinder now spans Z = -1–7, extending 1 mm beyond each plate face, with its center 36 mm along X from the old hole.</p>
<img src="https://assets.reactor3d.xyz/tutorials-page/articles/how-to-edit-stl-files/image-67ec2174-acac-427f-a80d-d3dd589828b6-1600x900-409ee1661d8d.webp" alt="New Hole Cutter at world X 18, Y zero and Z minus 1 with zero rotations and scale one" style="display:block;margin:0 auto" />

<h2>08. Cut the smaller hole</h2>
<p>Select <strong>Filled Plate</strong> first, then Ctrl-select <strong>New Hole Cutter</strong>. Click <strong>Cut operation</strong>, check <strong>Filled Plate</strong> as <strong>Target part</strong> and <strong>New Hole Cutter</strong> as the only <strong>Tool part</strong>, and keep <strong>Keep source parts</strong> off.</p>
<p>Click <strong>Confirm</strong> and name the result <strong>Edited Plate</strong>. The preview and result should show an open hole on the right, with the old left opening filled.</p>
<img src="https://assets.reactor3d.xyz/tutorials-page/articles/how-to-edit-stl-files/image-fbea63ad-4af9-4ecd-a28e-4089d46d59e3-1600x900-fb998f9bd6a6.webp" alt="Cut panel with Filled Plate as the target and New Hole Cutter as the selected tool" style="display:block;margin:0 auto" />

<h2>09. Download the edited STL</h2>
<p>Select <strong>Edited Plate</strong> and choose <strong>File → Export STL</strong>. Set <strong>Currently selected models</strong> and check the count is <strong>1</strong>; leave <strong>Project precision</strong> selected, then click <strong>Download in browser</strong> to save the STL.</p>
<p>Import the downloaded file into your slicer using millimeters and place the broad bottom face on the build plate. The exercise uses chosen modeling dimensions rather than a tested hardware clearance.</p>
<img src="https://assets.reactor3d.xyz/tutorials-page/articles/how-to-edit-stl-files/image-c223a967-18a8-4ab8-b21a-71db7bb96509-1600x900-f28034919f3f.webp" alt="STL export dialog with one currently selected model, Project precision and Download in browser available" style="display:block;margin:0 auto" />

<h2>Finished result</h2>
<p>The edited mesh is one plate with the original 70 × 40 × 6 mm envelope. Its old 10 mm hole is filled, and a 6 mm through-hole sits at X = 18 / Y = 0. The exported STL carries the resulting geometry; the RD practice projects retain the editable Reactor 3D workflow.</p>
<h2>Practical tips</h2>
<p>Match a filling tool to the plate's exact thickness, but extend a cutting tool beyond both faces. That combination preserves the exterior while avoiding a cut that only touches a surface. When changing one hole in another STL, measure that local region and move or resize the tools; scaling the whole model would also change its other dimensions.</p>
<h2>Practice downloads and source</h2>
<p>The <a href="https://github.com/IRROBOT/stl-editing-practice">companion GitHub repository</a> includes the starting and edited STL meshes, both native RD projects, screenshots and download checksums. The completed sample contains a small engraved attribution mark; no physical print or hardware-fit test is claimed.</p>
<p>Originally published as <a href="https://reactor3d.xyz/en/tutorials/how-to-edit-stl-files">How to Edit STL Files</a> by Reactor 3D.</p>
]]></content:encoded></item></channel></rss>